2.08 inch Support Grayscale OLED, OLED Grayscale - REX025664A
2.08 inch Support Grayscale OLED, OLED Grayscale - REX025664A
2.08 inch Support Grayscale OLED, OLED Grayscale - REX025664A
2.08 inch Support Grayscale OLED, OLED Grayscale - REX025664A
2.08 inch Support Grayscale OLED, OLED Grayscale - REX025664A
2.08 inch Support Grayscale OLED, OLED Grayscale - REX025664A
2.08 inch Support Grayscale OLED, OLED Grayscale - REX025664A

2.08 inch 256x64 Support Grayscale Level OLED Display

Model No. REX025664A

REX025664A is a dot matrix 256x64 COG graphic type OLED module. The size of the screen is 2.08” diagonal with module dimension 60.5x19mm. This OLED module has built-in IC SSD1362, and boasts high contrast ratio 10,000 : 1. There are many interface options to choose from, including 3-Wire and 4-Wire SPI, I2C serial interface, 8-bit 6800, 8-bit 8080 parallel interface.

Logic supply voltage ranges from 2.8V-3.3V, the typical value is 3V. The range of operating temperature is -40~+80°C; storage temperature is-40~+85°C. REX025664A offers different types of FPC such as ZIF and Hotbar FPC. The available emitting colors are white, yellow and it also features grayscale (Grayscale OLED).

★OLED Support Grayscale
★ Other FPC options available

Data source ref: REX025664AYAP3N00H00

Inquiry or Demo Code Datasheet Datasheet Back Previous Next
  • General Specs
  • Interface Pin Function
  • Contour Drawing
  • Absolute Maximum Ratings
  • Electrical Characteristics
  • Options
Item Dimension Unit
Structure COG
Size (Diagonal) 2.08 inch
Dot Matrix / Resolution 256 × 64 dots
Module Dimension 60.5 × 19.0 × 1.61 mm
View Area 53.18 × 14.78 mm
Active Area 51.18 × 12.78 mm
Dot / Pixel Size 0.18 × 0.18 mm
Dot / Pixel Pitch 0.20 × 0.20 mm
Emitting Color OLED, White / Yellow
Support Grayscale Yes
Display Mode Passive Matrix
Gray Scale 4 Bits
IC SSD1362
Interface 3-Wire and 4-Wire SPI, I2C, 8-bit 6800, 8-bit 8080
Power Supply 3V
Duty 1/64 duty
Storage Temperature -40~+80 °C
Polarizer Type -40~+85
FPC Options Yes
Type OLED Graphic Display, Grayscale OLED
No. Symbol Function
1 NC These pins are reserved. Nothing should be connected to these pins, nor are they connected together.
2 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
3 VP This pin is the segment pre-charge voltage reference pin.
A capacitor should be connected between this pin and VSS.
No external power supply is allowed to connect to this pin.
4 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
No external power supply is allowed to connect to this pin.
5 VDD Power supply for core logic operation.
VDD can be supplied externally (within the range of 1.65V to 2.6V) or regulated internally from VCI when VCI is >2.6V.
A capacitor should be connected between VDD and VSS under all circumstances.
6 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
7 IREF This pin is the segment output current reference pin.
When external IREF is used, a resistor should be connected between this pin and VSS to maintain current of around 18.75uA.
When internal IREF is used, this pin should be kept NC.
8 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
9 NC These pins are reserved. Nothing should be connected to these pins, nor are they connected together.
10 VSS Ground pin. It must be connected to external ground.
11 VSS Ground pin. It must be connected to external ground.
12 VCI Low voltage power supply.
VCI must always be equal to or higher than VDD and VDDIO.
13 BS0 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1, BS0 are pin select.
BS[2:0] Interface
000 4 line SPI
001 3 line SPI
110 8-bit 8080 parallel
100 8-bit 6800 parallel
010 I2C
Note  (1) 0 is connected to VSS  (2) 1 is connected to VCI
14 BS1
16 BS2
15 VCI Low voltage power supply.
VCI must always be equal to or higher than VDD and VDDIO.
17 CS This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS is pulled LOW (active LOW).
In I2C mode, this pin must be connected to VSS.
18 RES This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
19 D/C This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
20 R/W This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
21 RD This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
22 D0 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SID.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
23 D1
24 D2
25 D3
26 D4
26 D5
28 D6
29 D7
30 NC These pins are reserved. Nothing should be connected to these pins, nor are they connected together.
31 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.

REX025664A with Hotbar FPC

2.08 inch Support Grayscale OLED Display with Hotbar FPC- REX025664A

 

REX025664A with ZIF FPC

2.08 inch Support Grayscale OLED Display with ZIF FPC- REX025664A

Parameter Symbol Min Max Unit
Supply Voltage for Operation VCI -0.5 5.5 V
Supply Voltage for Logic VDD -0.5 2.75 V
Supply Voltage for Display VCC -0.5 21 V
Operating Temperature TOP -40 +80 °C
Storage Temperature TSTG -40 +85 °C

DC Electrical Characteristics

Item Symbol Condition Min Typ Max Unit
Supply Voltage for Logic VCI 2.8 3.0 3.3 V
Supply Voltage for Display VCC 11.5 12.0 12.5 V
Input High Volt. VIH 0.8×VCI VCI V
Input Low Volt. VIL VSS 0.2×VCI V
Output High Volt. VOH 0.9×VCI VCI V
Output Low Volt. VOL VSS 0.1×VCI V
50% Check Board operating Current ICC VCC=12V 15 30 mA

FPC options

Drawing FPC Length PIN Pitch ZIF / HOTBAR FPC Interface FPC No. Create Date
 FPC2070002401XXXXX02_REX025664A 23 24 0.7 HOTBAR 3-Wire and 4-Wire SPI, I2C, 6800, 8080 FPC2070002401XXXXX02 20180611
 FPC2030003111XXXXX02_REX025664A 21 31 0.3 ZIF 3-Wire and 4-Wire SPI, I2C, 6800, 8080 FPC2030003111XXXXX02 20171107
Top