- General Specs
- Interface Pin Function
- Contour Drawing
- Other Specifications
- Display Usage
- Description
- GUI Builder
| Item | Dimension | Unit |
|---|---|---|
| Size (Diagonal) | 3.5 | inch |
| Dot Matrix / Resolution | 320 × 3 (RGB) × 240 | dots |
| Module Dimension | 100 (W) × 82 (H) × 13.2(D) | mm |
| Viewing Area | 71 (W) × 53.51 (H) | mm |
| Active Area | 70.08 (W) × 52.56 (H) | mm |
| Dot / Pixel Pitch | 0.219 (W) × 0.219 (H) | mm |
| LCD Type | TFT, Normally Black, Transmissive | |
| View Direction | 80/80/80/80 (IPS) | |
| Aspect Ratio | 4:3 | |
| Control Board | Yes | |
| System Interface | CAN Bus differential ± 3.3 | |
| Protocol | CAN open | |
| I/O(GPIO) | No | |
| MCU | STM32F750 | |
| Detect Points | 1 | Points |
| Touch Panel | Projected Capacitive Touch Screen, PCAP | |
| Surface | Glare | |
| Brightness | 400 | cd/㎡ |
| Operating voltage | 5 ~ 24 | Vdc |
| Flash Memory Size | 16 | MB |
| SDRAM Frequency | 108 | Mhz |
| Operating Temperature | -20~+70 | °C |
CON2 Definition
| Pin No. | Symbol | Function | Remark |
|---|---|---|---|
| 16 | VIN | Power +5V~24V | Input |
| 15 | GND | Power GND | Input |
| 14 | CAN_H | CAN bus D+ | I/O |
| 13 | CAN_L | CAN bus D- | I/O |
| 12-1 | Reserved | -- | -- |
CON3 Definition
| Pin No. | Symbol | Function | Remark |
|---|---|---|---|
| 16 | +3V3 | 3.3V power for JTAG interface | Output |
| 15 | SWCLK | CLK pin for JTAG interface | Input |
| 14 | GND | GND for JTAG interface | Output |
| 13 | SWDI | Data pin for JTAG interface | I/O |
| 12 | NRST | Reset pin for JTAG interface | Input |
| 11 | SWDO | Data pin for JTAG interface | I/O |
| 10-1 | Reserved | -- | -- |
Smart TFT Display Mechanical Dimensions and Layout
Absolute Maximum Ratings
| Item | Symbol | Min | Typ | Max | Unit |
|---|---|---|---|---|---|
| Operating Temperature | TOP | -20 | － | +70 | ℃ |
| Storage Temperature | TST | -30 | － | +80 | ℃ |
Electrical Characteristics
| Item | Symbol | Min | Typ | Max | Unit |
|---|---|---|---|---|---|
| Supply Voltage | VCC | 5 | 12 | 24 | V |
| Supply Current | ICC | - | 150 | - | mA |
Bom
| Item | Description |
|---|---|
| LCM | RFC350X-AYW-DNG |
| PCBA | SV100035000XA00N0101 |
Functional description
Smart Display can be used to display the coordinate, status and data information provided by the connected HOST device. Customers can configure the position coordinates they want to display in normal operation mode (Node ID = 0x7B).
The Display is designed to be easily connected to a controller network, and to operate with minimum setup or knowledge of the SDO configuration on the controllers.
Splash Screen
The default splash image is shown below.
This product is produced as a generic product. If you require a custom splash image for your application, contact us to discuss.
Default Selection
Press the preferred application and hold for 3 seconds for the first time power on.
Acquisition of Displayed Data
The Smart Display can acquire the data that it displays either using the CANopen SDO protocol, or using the CANopen PDO protocol.
On Pre-operational mode, customers can set the coordinates of objects through SDO; On operational mode, customers can send data of objects through PDO.
Configuring the Display
Raystar Smart Display CAN series offers an out-of-the-box CANopen development experience that will lower customers' development costs and speed time-to-market expectations.
The Smart Display can use wide-temperature are designed to support control applications in harsh operating conditions, which designed to be connected to a variety of different situation combinations, such as automotive, marine, power generation and oil-and-gas.
The Smart Display comes with standard UI objects to get customers project off the ground quickly. If customers need custom UI objects support, our engineers are here to help. Send over your contents in PNG/JPG format, we will send over a new set of UI objects within 3~5 working days.
The Smart Display is defined as a slave device, which is controlled by master device via CAN bus command to render display content on the display screen and return touch event data with protocol objects.
Example Screen Layout (Industry application)
Example Layout
The screen layout described in this section is intended to demonstrate the settings of screen items that can be used in an industry application situation.
Example Screen Layout (Vehicle Application)
Example Layout
The screen layout described in this section is intended to demonstrate the settings of screen items that can be used in a vehicle automotive situation.
Example Screen Layout (Medical Application)
Example Layout
The screen layout described in this section is intended to demonstrate the settings of screen items that can be used in a Medical application situation.
RL0F00035000XGAAASA00, this 3.5-inch CAN bus Smart TFT LCD Display adopts one of our off-the-shelf IPS TFT modules RFC350X-AYW-DNG coupled with coding firmware interface. In the light of the coding firmware, users only need to execute commands of control which cut down on time of programming notably. Such smart display is an excellent solution for faster time-to-market.
The Smart Display of Raystar is comprised of our TFT module and CAN interface. There are plenty of advantages of this interface including data transmission of long distance (up to 40 meters), being highly immune to electrical interference, good stability. CAN BUS is the most common physical layer; the maximum transmission rate can reach 1Mb/s (High-Speed CAN). It’s effortless to communicate with other devices supporting CANopen protocol, moreover, there’re various types of objects of control to choose from. On top of that, its flexible parameter control settings allow users for faster development.
Smart Display has built-in flash memory (Flash) to store fonts and graphic objects (Object Dictionary). The host can simultaneously control up to 30 Smart Displays and demonstrate different graphic objects. This Smart Display also provides standard UI objects enabling users to swiftly develop projects. If customers need customized UI objects, Raystar’s engineering team is able to provide you with comprehensive help and convert image files in PNG / JPG format into image control objects which can be completed in 3 to 5 working days.
We also provide demo set with all needed accessories for you to realize your GUI design on smart displays.
1. Introduction of Raystar Smart Display GUI Builder
1-1 Dragging Widgets & preview function:
Users are able to design their screen appearance by dragging widgets on Raystar GUI Builder, and you also get a live preview of the changes. With the concept of "what you see is what you get", this function is time-saving for screen appearance design.
1-2 Simulator function:
There’s no need to purchase the hardware (Smart Display) to demonstrate the display effects and interactive behaviors. Users only need to use Raystar GUI Builder application software simulator to simulate the display effects and functions on the computer which greatly reduce costs and speed up project development.
1-3 Change or build GUI design on the client-side:
Instead of creating graphical objects through the Raystar engineering team, customers can replace or create GUI designs by themselves. But if customers have any other demands, we can also provide custom-design graphics objects.
1-4 How to get Raystar’s GUI Builder?
All you need is to contact us through our website or send inquiries to our sales email address. We'll provide it free of charge.
2.Smart Display GUI Builder introduction of operation and toolbar
2-1 The Start screen of Smart Display GUI Builder
2-2 The design page of Smart Display GUI Builder
2-3 Customization by Smart Display GUI Builder
2-4 Simulation by Smart Display GUI Builder
2-5 HW device update
2-6 The settings of installation
Install USB2CAN Driver:
*Execute stlink_winusb_install.bat (Please contact us to get the file)
Install Microsoft Visual C++ 2015-2019 Redistributable (x86)
*Execute VC_redist.x86.exe (Please contact us to get the file)
Install Smart Display GUI Builder
*Execute RaystarSmartDisplayGUIBuilderSetup_v0.1.5.msi (Please contact us to get the file)
*An icon of “Raystar SmartDisplay GUI Builder” will be shown after installing
