128x64 dots ST7567S LCD Display Module - RX12864T1
128x64 dots ST7567S LCD Display Module - RX12864T1
128x64 dots ST7567S LCD Display Module - RX12864T1
128x64 dots ST7567S LCD Display Module - RX12864T1
128x64 dots ST7567S LCD Display Module - RX12864T1

128x64 dots ST7567S COG LCD Display Module

Model No. RX12864T1

RX12864T1 is an alternative series for RX12864T in response to Sitronix’ reduced production of chips. RX12864T1 is a 128x64 graphic COG LCD module with backlight. Module dimension is 38.0×26.42 mm; active area is 25.58×14.06 mm. There’s a built-in controller IC ST7567S supporting 8080, 6800 and 4-Line SPI interfaces. Logic power supply ranges from 2.7V-3.3V (Typical 3V). Operating temperature is between -20°C to +70°C; storage temperature covers from -30°C to +80°C. Feel free to contact us for various combinations of LED backlight and LCD colors.

Data source ref: RX12864T1-FHW

Inquiry or Demo Code Datasheet Back Previous Next
  • General Specs
  • Interface Pin Function
  • Contour Drawing
  • Absolute Maximum Ratings
  • Electrical Characteristics
Item Dimension Unit
Structure COG
Size (Diagonal) 1.15 inch
Dot Matrix / Resolution 128 × 64 dots
Module Dimension 38.0 × 26.42 × 8.8 mm
Viewing Area 29.58 × 16.22 mm
Active Area 25.58 × 14.06 mm
Dot / Pixel Size 0.18 × 0.20 mm
Dot / Pixel Pitch 0.20 × 0.20 mm
IC ST7567S
Interface 6800/8080/4-Line SPI
Power Supply 3V
Duty 1/65Duty ; 1/9Bias
Type Graphic LCD Display
Pin No. Symbol Description
1 VDD Power supply pin for logic.
2 VSS Ground pin, connected to 0V
3 CSB Chip select input pin.
4 NC NC
5 RSTB Hardware reset input pin
6 A0 It determines whether the access is related to data or
command.
7 RWR
C86 MPU Type RWR Description
H 6800 series R/W Read/Write control input pin.
R/W=“H”: read.
R/W=“L”: write.
L 8080 series /WR Write enable input pin.
Signals on D[7:0] will be latched at the rising edge of /WR signal.
RWR is not used 4-line SPI interface and should fix to “H” by VDD
8 ERD
C86 MPUType ERD Description
H 6800 series E Read/Write control input pin.
R/W=”H“: When E is “H”, D[7:0] are in output mode.
R/W=”L“: Signals on D[7:0] are latched at the falling edge of E signal.
L 8080 series /RD Read enable input pin.
When /RD is “L”, D[7:0] are in output mode.
ERD is not used in 4-Line SPI interface and should fix to “H” by VDD
9~16 D0~D7 When using 8-bit parallel interface: (6800 or 8080 mode)
8-bit bi-directional data bus. Connect to the data bus of 8-bit microprocessor.
When CSB is non-active (CSB=“H”), D[7:0] pins are high impedance
When using serial interface: 4-line SPI
D[0]=SCL: Serial clock input.
D[1]=SDA_IN: Serial data input.
D[2:3]=SDA_OUT: Serial data output.
D[1:3] must be connected together as SDA.
D[4:7]=(1,1,1,1): ID Pin. D[4:7] should fix to “H” or “L” by VDDH or VSSL.
ID[0:3] can be read 4-bit ID only for serial interface from D[4:7].
17 C86 C86 selects the microprocessor type in parallel interface mode.
PSB C86 Selected Interface
“L” “H” Serial 4-Line SPI Interface
“H” “L” Parallel 8080 Series MPU Interface
“H” “H” Parallel 6800 Series MPU Interface
18 PSB PSB selects the interface type: Serial or Parallel.

128x64 dots ST7567S LCD Display Module - RX12864T1

Item Symbol Min Typ Max Unit
Operating Temperature TOP -20 － +70 ℃
Storage Temperature TST -30 － +80 ℃
Input Voltage VI -0.3 － VDD+0.3 V
Digital Power Supply Voltage VDD-Vss -0.3 － 4.0 V
LCD Power supply voltage V0-XV0 -0.3 － 14.0 V
Item Symbol Condition Min. Typ. Max. Unit
Supply Voltage For Logic VDD-VSS － 2.7 3.0 3.3 V
Supply Voltage For LCD VOP Ta=-20℃
Ta=25℃
Ta=70℃		 －
8.9
－		 －
9.1
－		 －
9.3
－		 V
V
V
Input High Volt. VIH － 0.7VDD － VDD V
Input Low Volt. VIL － VSS － 0.3VDD V
Output High Volt. VOH － 0.8VDD － VDD V
Output Low Volt. VOL － VDD － 0.2VDD V
Supply Current IDD VDD=3.0V － － 1.5 mA

Related Products

Top