2.42-inch COG 8080 OLED Display 128x64 with PCB, Frame - REP012864AJ

2.42" COG 8080 OLED Display 128x64 with PCB, Frame

Model No. REP012864AJ(8080)

REP012864AJ OLED is a dot matrix 128x64 COG graphic-type OLED module with a frame. The REP012864AJ module has a PCB with screw holes and a peripheral circuit for easy mounting and usage. The active area size is 2.42" diagonal with module dimensions 75x52.7 mm. This OLED module has built-in IC CH1116 supporting 8080 interface, logic supply voltage ranges from 2.8V-3.3V, and the typical value is 3.0V. The available emitting colors are white and yellow. This OLED display boasts a 10,000:1 high contrast ratio.

Data source ref: REP012864AJYPP3N00000

Inquiry or Demo Code Datasheet Back Previous Next

General Specs
Interface Pin Function
Contour Drawing
Absolute Maximum Ratings
Electrical Characteristics

Item	Dimension	Unit
Structure	COG+FR+PCB
Size (Diagonal)	2.42	inch
Dot Matrix / Resolution	128 × 64	dots
Module Dimension	75.0 × 52.7 × 8.5(Max)	mm
Active Area	55.01 × 27.49	mm
Dot / Pixel Size	0.40 × 0.40	mm
Dot / Pixel Pitch	0.43 × 0.43	mm
Emitting Color	OLED, White / Yellow
Display Mode	Passive Matrix
IC	CH1116
Interface	8080
Power Supply	3V
Duty	1/64 duty
Operating Temperature	-40~+80	°C
Storage Temperature	-40~+85	°C
Type	OLED Graphic Display

No.	Symbol	Function
1	VDD	Power supply input
2	VSS	Ground.
3	NC	No connection
4~11	D0~D7	This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
12	___ CS	This pad is the chip select input. When /CS = “L”, then the chip select becomes active, and data/command I/O is enabled.
13	NC	No connection
14	___ RES	This is a reset signal input pad. When /RES is set to “L”, the settings are initialized. The reset operation is performed by the /RES signal level.
15	___ WR	This is a MPU interface input pad. When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU /WR signal. The signals on the data bus are latched at the rising edge of the /WR signal.
16	A0	This is the Data/Command control pad that determines whether the data bits are data or a command. A0 = “H”: the inputs at D0 to D7 are treated as display data. A0 = “L”: the inputs at D0 to D7 are transferred to the command registers.
17	___ RD	This is a MPU interface input pad. When connected to an 8080 series MPU, it is active LOW. This pad is connected to the /RD signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”.
18	NC	No connection
19	DISP	Display off when it's pulled low; Display on when it's pulled high.
20	NC	No connection

* 80 Series Interface is default

2.42-inch COG 8080 OLED Display 128x64 with PCB, Frame - REP012864AJ

Parameter	Symbol	Min	Max	Unit
Supply Voltage for Logic	VDD	-0.3	3.6	V
Operating Temperature	TOP	-40	+80	°C
Storage Temperature	TSTG	-40	+85	°C

DC Electrical Characteristics

Item	Symbol	Condition	Min	Typ	Max	Unit
Supply Voltage for Logic	VDD	－	2.8	3.0	3.3	V
High Level Input	VIH	－	0.8×VDD	－	VDD	V
Low Level Input	VIL	－	VSS	－	0.2×VDD	V
High Level Output	VOH	－	0.8×VDD	－	VDD	V
Low Level Output	VOL	－	VSS	－	0.2×VDD	V
Display 50% Pixel on	IDD	VDD =3.0V	－	60	120	mA