SSD1315 OLED Graphic Display Module 128x64, 0.96 inch - REX012864V
SSD1315 OLED Graphic Display Module 128x64, 0.96 inch - REX012864V
SSD1315 OLED Graphic Display Module 128x64, 0.96 inch - REX012864V
SSD1315 OLED Graphic Display Module 128x64, 0.96 inch - REX012864V
SSD1315 OLED Graphic Display Module 128x64, 0.96 inch - REX012864V

0.96" 128x64 SSD1315 OLED Graphic Display Module

Model No. REX012864V

REX012864V is a COG graphic OLED display module with resolution 128x64. This module is designed to be a cost-effective, consumer-grade model, and this advantage makes it a good fit for price-sensitive markets. It also boasts high contrast ratio 10000:1 and higher brightness compared to same grade products on the market. This 0.96” COG graphic OLED module is suitable to be used on applications such as wearable devices, smart home appliance etc. The module works within temperature range from -30℃to +70℃; storage temperature is-30℃to +70℃.

Data source ref: REX012864VWPP3N0Y000

Inquiry or Demo Code Datasheet Back Previous Next
  • General Specs
  • Interface Pin Function
  • Contour Drawing
  • Absolute Maximum Ratings
  • Electrical Characteristics
Item Dimension Unit
Structure COG
Size (Diagonal) 0.96 inch
Dot Matrix / Resolution 128 × 64 dots
Module Dimension 24.74 × 16.90 × 1.26 mm
View Area 22.74 × 11.86 mm
Active Area 21.74 × 10.86 mm
Dot / Pixel Size 0.15 × 0.15 mm
Dot / Pixel Pitch 0.17 × 0.17 mm
Emitting Color OLED, White / Yellow
Display Mode Passive Matrix
IC SSD1315
Interface 3-Wire/4-Wire SPI / I2C
Power Supply 3V
Duty 1/64 duty
Operating Temperature -30~+70 °C
Storage Temperature -30~+70 °C
Polarizer Type Polarizer optional
Type OLED Graphic Display
No. Symbol Function
1 C2N C2P/C2N – Pin for charge pump capacitor; Connect to each other with a capacitor.
2 C2P
3 C1P C1P/C1N – Pin for charge pump capacitor; Connect to each other with a capacitor.
4 C1N
5 VBAT Power Supply for DC/DC Converter Circuit
This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be float when the converter is not used.
6 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
When charge pump is enabled, a capacitor should be connected between this pin and VSS.
7 VSS Ground of Logic Circuit
This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground.
8 VDD Power Supply for Logic
This is a voltage supply pin. It must be connected to external source.
9 BS0 Communicating Protocol Select
These pins are MCU interface selection input. See the
following table:
BS[1:0] Interface
00 4-line SPI
01 3-line SPI
10 I2C
10 BS1
11 CS# Chip Select
This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low.
12 RES# Power Reset for Controller and Driver
This pin is reset signal input. When the pin is low, initialization of the chip is executed.
13 D/C# In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
14~16 D0~D2 When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
17 IREF Current Reference for Brightness Adjustment
This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 30uA.
18 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
19 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
When charge pump is enabled, a capacitor should be connected between this pin and VSS.
20 VLSS Ground of Analog Circuit
This is an analog ground pin. It should be connected to VSS externally.

SSD1315 OLED Graphic Display Module 128x64, 0.96 inch - REX012864V

Parameter Symbol Min Max Unit
Supply Voltage for Logic VDD -0.3 4.0 V
Charge Pump Regulator VBAT -0.3 6.0 V
Supply Voltage for Display VCC 0 18.0 V
Operating Temperature TOP -30 +70 °C
Storage Temperature TSTG -30 +70 °C

DC Electrical Characteristics

Item Symbol Condition Min Typ Max Unit
Supply Voltage for Logic VDD 2.8 3.0 3.3 V
Supply Voltage for Display VCC 7.0 7.5 8.0 V
Input High Volt. VIH 0.8×VDD VDD V
Input Low Volt. VIL 0 0.2×VDD V
Output High Volt. VOH 0.9×VDD VDD V
Output Low Volt. VOL 0 0.1×VDD V
Operating Current for VCC (50% display ON) ICC 6 12 mA
Top