- General Specs
- Interface Pin Function
- Contour Drawing
- Other Specifications
- Description
- GUI Builder
| Item | Dimension | Unit |
|---|---|---|
| Size (Diagonal) | 4.3 | inch |
| Dot Matrix / Resolution | 480 × RGB × 272 (TFT) | dots |
| PCB | 119.3 (W) × 67.2 (H) × 1.6 (D) | mm |
| Housing Outline | NA | mm |
| Module Dimension | 119.3 (W) × 67.2 (H) × 12.45 (D) | mm |
| Viewing Area | 98.16 (W) × 56.856 (H) | mm |
| Active Area | 95.04 (W) × 53.856 (H) | mm |
| Dot / Pixel Pitch | 0.198 (H) × 0.198 (V) | mm |
| LCD Type | TFT, Normally Black, Transmissive | |
| View Direction | 80/80/80/80 (IPS) | |
| Aspect Ratio | 16:9 | |
| Control Board | Yes | |
| System Interface | RS485 | |
| Protocol | Modbus | |
| I/O(GPIO) | No | |
| MCU | STM32F750 | |
| Detect Points | 1 | Points |
| Touch Panel | Projected Capacitive Touch Screen, PCAP | |
| Surface | Glare | |
| Brightness | Min: 300; Typ: 400 | cd/㎡ |
| Operating voltage | 5 ~ 24 | Vdc |
| Flash Memory Size | 16 | MB |
| SDRAM Frequency | 108 | Mhz |
| Operating Temperature | -30~+80 | °C |
CN1 Definition
| Pin | Symbol | Function | Remark |
|---|---|---|---|
| 1 | GND | GND | Output |
| 2 | RS485+ | RS485 D+ | I/O |
| 3 | RS485- | RS485 D- | I/O |
| 4 | +5V | VIN | Input |
| 5 | GND | GND | Output |
| 6-7 | NC | - | - |
| 8 | +5V | VIN | Input |
| 9-10 | NC | - | - |
| 11-12 | GND | GND | Output |
| 13-14 | NC | - | - |
| 15 | GND | Power GND | Input |
| 16 | +5V | Power +5V ~ +24V | Input |
CN2 Definition
| Pin | Symbol | Function | Remark |
|---|---|---|---|
| 1-9 | NC | - | - |
| 10 | GND | GND | Output |
| 11 | JTAG_SWDO | Data pin for JTAG interface | I/O |
| 12 | NRST | Reset pin for JTAG interface | Input |
| 13 | JTAG_SWDI | Data pin for JTAG interface | I/O |
| 14 | GND | GND for JTAG interface | Output |
| 15 | JTAG_SWCLK | CLK pin for JTAG interface | Input |
| 16 | VDD3V | 3.3V power for JTAG interface | Output |
Absolute Maximum Ratings
| Item | Symbol | Min | Typ | Max | Unit |
|---|---|---|---|---|---|
| Operating Temperature | TOP | -30 | - | +80 | ℃ |
| Storage Temperature | TST | -30 | - | +80 | ℃ |
Electrical Characteristics
| Item | Symbol | Min | Typ | Max | Unit |
|---|---|---|---|---|---|
| Supply Voltage | VCC | 5 | 12 | 24 | V |
| Supply Current | ICC | - | 170 | - | mA |
Bom
| Item | Description |
|---|---|
| LCM | RFE43AW-AWW-DNG |
| PCBA | SV10004R300WA00N0104 |
RL0F00043000WGDAASA00 is a 4.3-inch Smart Display of RS485 series defined as a slave device, that is controlled by master device via RS485 command to render display content on the display screen and return touch event data with protocol objects.
RL0F00043000WGDAASA00 is integrated with a standard TFT module RFE43AW-AWW-DNG and 4-layer PCBA with built-in firmware. This 4.3-inch Smart Display is an easy-to-use product which allows customers to develop projects rapidly in a cost-effective way. This 4.3-inch Smart Display can work with computer with USB2RS485 dongle as HOST platform.
Raystar Smart Display RS485 Series offers an out-of-the-box Modbus development experience that will lower your development costs and speed up your time to market.
The RS485 Modbus smart displaycomes with standard UI objects to get customers project off the ground quickly. If customers need custom UI objects support, our engineers are here to help. Send over your contents in PNG/JPG format, we will customize a new set of UI objects to you.
We also provide demo set with all needed accessories for you to realize your GUI design on smart displays.
1. Introduction of Raystar Smart Display GUI Builder
1-1 Dragging Widgets & preview function:
Users are able to design their screen appearance by dragging widgets on Raystar GUI Builder, and you also get a live preview of the changes. With the concept of "what you see is what you get", this function is time-saving for screen appearance design.
1-2 Simulator function:
There’s no need to purchase the hardware (Smart Display) to demonstrate the display effects and interactive behaviors. Users only need to use Raystar GUI Builder application software simulator to simulate the display effects and functions on the computer which greatly reduce costs and speed up project development.
1-3 Change or build GUI design on the client-side:
Instead of creating graphical objects through the Raystar engineering team, customers can replace or create GUI designs by themselves. But if customers have any other demands, we can also provide custom-design graphics objects.
1-4 How to get Raystar’s GUI Builder?
All you need is to contact us through our website or send inquiries to our sales email address. We'll provide it free of charge.
2.Smart Display GUI Builder introduction of operation and toolbar
2-1 The Start screen of Smart Display GUI Builder
2-2 The design page of Smart Display GUI Builder
2-3 Customization by Smart Display GUI Builder
2-4 Simulation by Smart Display GUI Builder
2-5 HW device update
2-6 The settings of installation
Install USB2CAN Driver:
*Execute stlink_winusb_install.bat (Please contact us to get the file)
Install Microsoft Visual C++ 2015-2019 Redistributable (x86)
*Execute VC_redist.x86.exe (Please contact us to get the file)
Install Smart Display GUI Builder
*Execute RaystarSmartDisplayGUIBuilderSetup_v0.1.5.msi (Please contact us to get the file)
*An icon of “Raystar SmartDisplay GUI Builder” will be shown after installing
