2.7 inch 128x64 Graphic COG SSD1309 OLED with Capacitive Touchscreen + PCB + Frame - REP012864Q-CTP
2.7 inch 128x64 Graphic COG SSD1309 OLED with Capacitive Touchscreen + PCB + Frame - REP012864Q-CTP
2.7 inch 128x64 Graphic COG SSD1309 OLED with Capacitive Touchscreen + PCB + Frame - REP012864Q-CTP
2.7 inch 128x64 Graphic COG SSD1309 OLED with Capacitive Touchscreen + PCB + Frame - REP012864Q-CTP
2.7 inch 128x64 Graphic COG SSD1309 OLED with Capacitive Touchscreen + PCB + Frame - REP012864Q-CTP

2.7" 128x64 COG SSD1309 OLED with Capacitive Touchscreen + PCB + Frame

Model No. REP012864Q-CTP

REP012864Q-CTP is a dot matrix 128x64, 2.7 inch diagonal COG OLED display with capacitive touchscreen. The capacitive touch panel has built-in IC GT911, supporting 1-point touch. The size of the active area is 2.7” diagonal with module dimension 82×47.5 mm. The additional PCB on this OLED display helps users to save time on developing PCB on their own. Also, there's an added frame with four screw holes allowing users for quick mounting.

This 128x64 OLED module has built-in SSD1309 driver IC, and boasts high contrast ratio 10,000 : 1. There are many interface options to choose from, including 6800, 8080, 4-wire SPI, I2C interface. Logic supply voltage ranges from 2.8V-3.3V, the typical value is 3V. The available emitting colors are white, yellow, sky blue and green. The module can operate within the range of -20℃ to +70℃; storage temperature ranges from -30℃ to +80℃.

Data source ref: REP012864QWPP3L00000

Inquiry or Demo Code Datasheet Back Previous Next
  • General Specs
  • Interface Pin Function
  • Contour Drawing
  • Absolute Maximum Ratings
  • Electrical Characteristics
Item Dimension Unit
Structure COG + FR + PCB
Size (Diagonal) 2.7 inch
Dot Matrix / Resolution 128 × 64 dots
Module Dimension 82.0 × 47.5 × 8.65 mm
Viewing Area 63.41 × 33.69 mm
Active Area 61.41 × 30.69 mm
Dot / Pixel Size 0.45 × 0.45 mm
Dot / Pixel Pitch 0.48 × 0.48 mm
Emitting Color White / Yellow / Sky Blue / Green
Display Mode Passive Matrix
IC SSD1309
Interface 6800,8080,4-Wire SPI,I2C
PCAP IC GT911
PCAP Interface I2C
Detect Points 1 Points
Touch Panel Capacitive Touch Panel
Surface Glare
Power Supply 3V
Duty 1/64 duty
Operating Temperature -20~+70 °C
Storage Temperature -30~+80 °C
Polarizer Type Polarizer optional
Type OLED Graphic Display, OLED Touch Display
No. Symbol Function
1 VSS Ground.
2 VDD Power supply pin for core logic operation
3 NC No connection
4 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
5 R/W#
(WR#)		 This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
6 E(/RD#) This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
7-14 D0~D7 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
15 NC No connection
16 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
17 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
18 NC No connection
19 BS2 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select
  BS1 BS2
I2C 1 0
4-wire Serial 0 0
8-bit 68xx Parallel 0 1
8-bit 80xx Parallel 1 1
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
20 BS1
21 TP_SCK I2C clock signal
22 TP_SDA I2C data signal
23 TP_INT External interrupt signal, active low
24 TP_RST External reset signal, active low

2.7 inch 128x64 Graphic COG OLED with Capacitive Touchscreen + PCB + Frame - REP012864Q-CTP

Parameter Symbol Min Max Unit
Supply Voltage for Logic VDD -0.3 4 V
Operating Temperature TOP -20 +70 °C
Storage Temperature TSTG -30 +80 °C

DC Electrical Characteristics

Item Symbol Condition Min Typ Max Unit
Supply Voltage for Logic VDD － 2.8 3.0 3.3 V
High Level Input VIH － 0.8×VDD － － V
Low Level Input VIL － － － 0.2×VDD V
High Level Output VOH － 0.9×VDD － － V
Low Level Output VOL － － － 0.1×VDD V
50% Check Board operating Current VDD =3V － 175 350 mA

Touch Panel Controller GT911

Item Symbol Min Typ Max Unit
Input High Volt. VIH 0.75xVDD   VDD+0.3 V
Input Low Volt. VIL -0.3 － 0.25xVDD V
Output High Volt. VOH 0.85xVDD － － V
Output Low Volt. VOL － － 0.15xVDD V

Related Products

Top