- General Specs
- Interface Pin Function
- Contour Drawing
- Absolute Maximum Ratings
- Electrical Characteristics
Item | Dimension | Unit |
---|---|---|
Structure | COG+PCB | |
Size (Diagonal) | 2.42 | inch |
Dot Matrix / Resolution | 128 × 64 | dots |
Module Dimension | 75.0 × 52.7 × 10.2 (MAX) | mm |
Viewing Area | 57.01 × 29.49 | mm |
Active Area | 55.01 × 27.49 | mm |
Dot / Pixel Size | 0.40 × 0.40 | mm |
Dot / Pixel Pitch | 0.43 × 0.43 | mm |
Emitting Color | OLED, White / Yellow / Green / Sky Blue | |
Display Mode | Passive Matrix | |
IC | SSD1309 | |
Interface | 8080 option 6800, 4-SPI, I2C | |
PCAP IC | GT911 | |
PCAP Interface | I2C | |
Detect Points | 1 | Points |
Touch Panel | Capacitive Touch Panel | |
Surface | Normal Glare | |
Power Supply | 3V | |
Duty | 1/64 duty | |
Operating Temperature | -20~+70 | °C |
Storage Temperature | -30~+80 | °C |
Polarizer Type | Polarizer optional | |
Type | OLED Graphic Display, OLED Touch Display |
No. | Symbol | Function |
---|---|---|
1 | VDD | Power supply pin for core logic operation |
2 | VSS | Ground. |
3 | NC(GND) | No connection |
4~11 | D0~D7 | These pins are bi-directional data bus connecting to the MCU data bus. Unused pins are recommended to tie LOW. |
12 | CS# | This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW). |
13 | NC(GND) | No connection |
14 | RES# | This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
15 | R/W# | This pin is read / write control input pin connecting to the MCU interface. When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW. |
16 | D/C# | This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data. When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register. |
17 | E | This pin is MCU interface input. When 6800 interface mode is selected, this pin will be used as the Enable (E) signal. |
18 | NC(GND) | No connection |
19 | DISP | No Connection |
20 | NC(GND) | No connection |
21 | TP_INT | Interrupt signal, active low, asserted to request Host start a new transaction |
22 | TP_SDA | I2C data signal |
23 | TP_SCL | I2C clock signal |
24 | TP_RST | External reset signal, active low |
Parameter | Symbol | Min | Max | Unit |
---|---|---|---|---|
Supply Voltage for Logic | VDD | -0.3 | 4 | V |
Operating Temperature | TOP | -20 | +70 | °C |
Storage Temperature | TSTG | -30 | +80 | °C |
DC Electrical Characteristics
Item | Symbol | Condition | Min | Typ | Max | Unit |
---|---|---|---|---|---|---|
Supply Voltage for Logic | VDD | - | 2.8 | 3.0 | 3.3 | V |
High Level Input | VIH | - | 0.8×VDD | - | - | V |
Low Level Input | VIL | - | - | - | 0.2×VDD | V |
High Level Output | VOH | - | 0.9×VDD | - | - | V |
Low Level Output | VOL | - | - | - | 0.1×VDD | V |
50% Check Board operating Current | IDD | VDD =3V | - | 150 | 300 | mA |