1.71-inch graphic COG OLED display (CH1115) with PCB - REA012832P

1.71-inch graphic COG OLED display (CH1115) with PCB

Model No. REA012832P

REA012832P is 1.71-inch graphic COG OLED display with PCB. This resolution of this display is 128x32 pixels. This OLED module has built-in IC CH1115 supporting 4-Wire SPI interface. Features:
1. I/F provides a standard PIN (2.54mm pinhole) row to facilitate customers to connect the module with their applications.
2. The boost circuit is equipped on the PCB board, so customers can simply provide a set of VDD voltage to use the module.
3. The PCB board's screw-hole design allows customers to mount the module easily.
4. High contrast ratio 10,000:1 making the visual performance stand out from traditional displays.

Logic supply voltage ranges from 1.8V-3.3V; typical value is 3V. The module works within temperature from -40℃ to +80℃; Storage temperature range is -40℃ to +85℃.

Data source ref: REA012832PWAP3N00000

Inquiry or Demo Code Datasheet Back Previous Next

General Specs
Interface Pin Function
Contour Drawing
Absolute Maximum Ratings
Electrical Characteristics

Item	Dimension	Unit
Structure	COG + PCB
Size (Diagonal)	1.71	inch
Dot Matrix / Resolution	128 × 32	dots
Module Dimension	60.0 × 18.75 × 5.96 (MAX)	mm
Viewing Area	44.22 × 12.54	mm
Active Area	42.22 × 10.54	mm
Dot / Pixel Size	0.308 × 0.308	mm
Dot / Pixel Pitch	0.33 × 0.33	mm
Emitting Color	OLED, White / Yellow
Display Mode	Passive Matrix
IC	CH1115
Interface	4-Wire SPI
Power Supply	3V
Duty	1/32 duty
Operating Temperature	-40~+80	°C
Storage Temperature	-40~+85	°C
Polarizer Type	Polarizer optional
Type	OLED Graphic Display

No.	Symbol	Function
1	GND	Ground.
2	VCC	Power supply pin for logic.
3	D0	When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI).
4	D1
5	RES#	This is a reset signal input pad. When RES# is set to “L”, the settings are initialized. The reset operation is performed by the RES# signal level.
6	D/C#	This is the Data/Command control pad that determines whether the data bits are data or a command. D/C = “H”: the inputs at D0 and D1 are treated as display data. D/C = “L”: the inputs at D0 and D1 are transferred to the command registers.
7	CS#	This pad is the chip select input. When CS# = “L”, then the chip select becomes active, and data/command I/O is enabled.

1.71-inch graphic COG OLED display (CH1115) with PCB - REA012832P

Parameter	Symbol	Min	Max	Unit
Supply Voltage for Logic	VCC	-0.3	3.6	V
Operating Temperature	TOP	-40	+80	°C
Storage Temperature	TSTG	-40	+85	°C

DC Electrical Characteristics

Item	Symbol	Condition	Min	Typ	Max	Unit
Supply Voltage for Logic	VCC	－	1.8	3.0	3.3	V
High Level Input	VIH	－	0.8×VCC	－	VCC	V
Low Level Input	VIL	－	GND	－	0.2×VCC	V
High Level Output	VOH	－	0.8×VCC	－	VCC	V
Low Level Output	VOL	－	GND	－	0.2×VCC	V
Display 50% Pixel on	ICC	VCC =3V	－	35	70	mA