Capacitive Touchscreen TFT LCD 3.5 with Controller Board - RFC350Q-EIW-DBG
Capacitive Touchscreen TFT LCD 3.5 with Controller Board - RFC350Q-EIW-DBG

Capacitive Touchscreen TFT LCD 3.5" with Controller Board

Model No. RFC350Q-EIW-DBG

RFC350Q-EIW-DBG is one of the models in our Q series--- 3.5-inch TFT-LCD display module with controller board and PCAP touch. The resolution of this module is 320 x 240 pixels, and it has 4 screw holes & metal frame allowing for quick mounting. The Q series mainly uses IC SSD1963. TFT modules of this series are all characterized by 36-pin MCU 8080 8/16-bit pin define, and the 8/16-bit 6800 pin define interface can be selected through Jump. Compared to the P series, functions of Q series are simple and pricing is relatively lower.

The brightness is 340 cd/m2 with contrast ratio 350:1. LCM voltage ranges from 3V-3.3V, typical value is 3.1V. Operating temperature covers from -20~+70℃, storage temperature range is from -30~+80℃.

Inquiry or Demo Code Datasheet Back Previous Next
  • General Specs
  • Interface Pin Function
  • Contour Drawing
  • Absolute Maximum Ratings
  • Electrical Characteristics
Item Dimension Unit
TFT Series TFT Panel with Controller Board
Size (Diagonal) 3.5 inch
Dot Matrix / Resolution 320 × RGB × 240 (TFT) dots
Module Dimension 93.5 × 66.44 × 8.89 mm
Active Area 70.08 × 52.56 mm
Dot / Pixel Pitch 0.073 × 0.219 mm
LCD Type TFT, Normally White, Transmissive
View Direction 12 o’clock
Gray Scale Inversion Direction 6 o’clock
Aspect Ratio 4:3
Backlight Type LED, Normally White
Control Board Yes
Built-in Controller SSD1963
Interface Digital 8080 family MPU 8bit/16bit
PCAP FW Version 0x07.0x00.0x00.0x00.0x00.0x35.0x5A.0x01
PCAP IC ILI2130 or equivalent
PCAP Interface I2C
PCAP Resolution 16384*16384
Detect Points 5 Points
Touch Panel Projected capacitive touch panel, PCAP
Surface Glare
Brightness 340 cd/㎡
Mounting Hole Yes
Operating Temperature -20~+70 °C
Storage Temperature -30~+80 °C
Pin Symbol Function
1 GND System ground pin of the IC.   
Connect to system ground.
2 VDD Power Supply : +3.3V
3 BL_E Backlight control signal , H: On \ L: Off
4 D/C Data/Command select
5 WR Write strobe signal
6 RD Read strobe signal
7 DB0 Data bus
8 DB1 Data bus
9 DB2 Data bus
10 DB3 Data bus
11 DB4 Data bus
12 DB5 Data bus
13 DB6 Data bus
14 DB7 Data bus
15 DB8 Data bus
16 DB9 Data bus (When select 8bits Mode, this pin is NC)
17 DB10 Data bus (When select 8bits Mode, this pin is NC)
18 DB11 Data bus (When select 8bits Mode, this pin is NC)
19 DB12 Data bus (When select 8bits Mode, this pin is NC)
20 DB13 Data bus (When select 8bits Mode, this pin is NC)
21 DB14 Data bus (When select 8bits Mode, this pin is NC)
22 DB15 Data bus (When select 8bits Mode, this pin is NC)
23 NC No connect
24 CTP_INT External interrupt to the host
25 CS Chip select
26 RST Hardware reset
27 NC No connect
28 NC No connect
29 CTP_SCL I2C clock input
30 CTP_SDA I2C data input and output
31 CTP_RST External Reset, Low is active
32 NC No connect
33 VLED- VLED- for B/L  LED inverter  (GND)
34 VLED- VLED- for B/L  LED inverter  (GND)
35 VLED+ VLED+ for B/L  LED inverter  (+3.3V)
36 VLED+ VLED+ for B/L  LED inverter  (+3.3V)

Capacitive Touchscreen TFT LCD 3.5 with Controller Board - RFC350Q-EIW-DBG

Item Symbol Min Typ Max Unit
Operating Temperature TOP -20 － 70 ℃
Storage Temperature TST -30 － 80 ℃

Operating conditions: (CON2.Pin1=GND, Pin2=VDD)

Item Symbol Condition Min Typ Max Unit
Supply Voltage For LCM VDD － 3.0 3.1 3.3 V
Supply Current For LCM IDD — — 210 350 mA
Supply CTP VDDT — 3.0 3.3 3.6 V
ICTP — － 45 68 mA

Backlight driving conditions (CON2.Pin33,34=VLED-, Pin35,36=VLED+)

Parameter Symbol Min Typ Max Unit
Operation Current For LED Driver VLED=3.3V 150 - 225 mA
Power Consumption VLED=3.3V 495 - 742.5 mW
Supply Voltage For LED Driver VLED+ 3.3 - 5 V
LED Life Time   - 50,000 - Hr

Related Products

Top