LCD COG Display Module 128x64 - RX12864D2
LCD COG Display Module 128x64 - RX12864D2
LCD COG Display Module 128x64 - RX12864D2
LCD COG Display Module 128x64 - RX12864D2
LCD COG Display Module 128x64 - RX12864D2

LCD COG Display Module 128x64

Model No. RX12864D2

RX12864D2 is a COG 128x64 graphic LCD display module with backlight. Module dimension is 90.0×52.8 mm; active area is 66.52×33.24 mm. There’s a built-in controller IC ST7565P supporting 8080, 6800 and SPI interfaces. Logic power supply ranges from 2.7V-3.3V (Typical 3V). Operating temperature is between -20°C and +70°C; storage temperature covers from -30°C to +80°C. Feel free to contact us for various combinations of LED backlight and LCD colors.

Data source ref: RX12864D2-FHW

Inquiry or Demo Code Datasheet Back Previous Next
  • General Specs
  • Interface Pin Function
  • Contour Drawing
  • Absolute Maximum Ratings
  • Electrical Characteristics
Item Dimension Unit
Structure COG
Dot Matrix / Resolution 128 × 64 dots
Module Dimension 90.0 × 52.8 × 6.6 (MAX) mm
Viewing Area 70.7 × 38.8 mm
Active Area 66.52 × 33.24 mm
Dot / Pixel Size 0.48 × 0.48 mm
Dot / Pixel Pitch 0.52 × 0.52 mm
IC ST7565P or Equivalent
Interface 6800 / 8080 / SPI
Power Supply 3.3V
Duty 1/64 duty cycle, 1/9 Bias
Type Graphic LCD Display
Pin No. Symbol Level Description
1 /CS1   This is the chip select signal. When /CS1 = “L” , then the
chip select becomes active, and data/command I/O is enabled.
2 /RES   When /RES is set to “L” , the settings are initialized.
3 A0   This is connect to the least significant bit of the normal MPU address bus, and it determines whether the data bits are data or a command.
A0 = “H”: Indicates that D0 to D7 are display data.
A0 = “L”: Indicates that D0 to D7 are control data.
4 /WR(R/W)   When connected to an 8080 MPU, this is active LOW.
(R/W) This terminal connects to the 8080 MPU /WR signal. The signals on the data bus are latched at the rising edge of the /WR signal.
When connected to a 6800 Series MPU:
This is the read/write control signal input terminal.
When R/W = “H”: Read.
When R/W = “L”: Write.
5 /RD(E)   When connected to an 8080 MPU, this is active LOW.
(E) This pin is connected to the /RD signal of the 8080 MPU, and the ST7565P series data bus is in an output status when this signal is “L”.
When connected to a 6800 Series MPU, this is active HIGH.
This is the 6800 Series MPU enable clock input terminal.
6 DB0   This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data
Bus.
7 DB1  
8 DB2  
9 DB3  
10 DB4  
11 DB5  
12 DB6  
13 DB7  
14 VDD   Shared with the MPU power supply terminal VDD. ( 3.3 V )
15 VSS   This is a 0V terminal connected to the system GND.
16 VOUT   DC/DC voltage converter. Connect a capacitor between this terminal and VSS.
17 CAP5+   DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1- terminal.
18 CAP3+   DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1- terminal.
19 CAP1-   DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1+ terminal.
20 CAP1+   DC/DC voltage converter. Connect a capacitor between this terminal and the CAP1- terminal.
21 CAP2+   DC/DC voltage converter. Connect a capacitor between this terminal and the CAP2- terminal.
22 CAP2-   DC/DC voltage converter. Connect a capacitor between this terminal and the CAP2+ terminal.
23 CAP4+   DC/DC voltage converter. Connect a capacitor between this terminal and the CAP2- terminal.
24 VRS   This is the externally-input VREG power supply for the LCD power supply voltage regulator.
25 V4   This is a multi-level power supply for the liquid crystal drive. The voltage Supply applied is determined by the liquid crystal cell, and is changed through the use of a resistive voltage divided or through changing the impedance using an op. amp.
Voltage levels are determined based on Vss, and must maintain the relative magnitudes shown below.
V0 ≧V1 ≧V2 ≧V3 ≧V4 ≧Vss
When the power supply turns ON, the internal power supply circuits produce the V1 to V4 voltages shown below. The voltage settings are selected using the LCD bias set command.
26 V3  
27 V2  
28 V1  
29 V0  
30 VR   Output voltage regulator terminal. Provides the voltage between VDD and V5 through a resistive voltage divider.
IRS = “L” : the V5 voltage regulator internal resistors are not used .
IRS = “H” : the V5 voltage regulator internal resistors are used .
31 C86   This is the MPU interface switch terminal.
C86 = “H”: 6800 Series MPU interface.
C86 = “L”: 8080 MPU interface.
32 P/S   This is the parallel data input/serial data input switch terminal.
P/S = “H”: Parallel data input.
P/S = “L”: Serial data input.
The following applies depending on the P/S status:

When P/S = “L”, D0 to D5 may be “H”, “L” or Open.
RD (E) and WR (R/W) are fixed to either “H” or “L”.
With serial data input, It is impossible read data from RAM .
33 /HPM   This is the power control terminal for the power supply circuit for liquid crystal drive.
HPM = “H”: Normal mode
HPM = “L”: High power mode
34 IRS   This terminal selects the resistors for the V5 voltage level adjustment.
IRS = “H”: Use the internal resistors
IRS = “L”: Do not use the internal resistors. The V5 voltage level is regulated by an external resistive voltage divider attached to the VR terminal

LCD COG Display Module 128x64 - RX12864D2

Item Symbol Min Typ Max Unit
Operating Temperature TOP -20 +70
Storage Temperature TST -30 +80
Power Supply Voltage VDD -0.3 3.6 V
Power supply voltage (VDD standard) V0, VOUT -0.3 14.5 V
Power supply voltage (VDD standard) V1, V2, V3, V4 -0.3 V0+0.3 V
Item Symbol Condition Min Typ Max Unit
Supply Voltage For Logic VDD-VSS 2.7 3.0 3.3 V
Supply Voltage For LCM V0-VSS Ta=-20℃
Ta=25℃
Ta=70℃
10.0
9.8
9.6
10.2
10.0
9.8
10.4
10.2
10.0
V
V
V
Input High Volt. VIH 0.8 VDD VDD V
Input Low Volt. VIL Vss 0.2 VDD V
Output High Volt. VOH 0.8 VDD VDD V
Output Low Volt. VOL Vss 0.2VDD V
Supply Current(LED backlight is not included) IDD VDD=3.0V   0.6 1 mA
Top